LAMBRETTA TOOL FOR THE LI FAMILY

, ,

Tools not only please the heart of a screwdriver, with the right tool the work is also easier to do.

Contrary to the usual myth that you need tons of special tools for the Lambretta, only a few tools are really essential.

ESSENTIALS CATEGORY It doesn't work without them

Allen key bgm PRO 3.5mm

Unusual size and used for the clamping nipples on the gearshift and clutch. The bgm key comes with a practical ball head. This means that the rear shift cable can also be reached when the clutch cable is attached and without a special control block.

 

flywheel

Rotor puller M27x1,25

(A – D, LI, LIS, SX, TV, DL, GP, J, Lui) 
8099000

Rotor puller M30 x 1,5

(motor place ignition)
8099013

Flywheel holder 2+3 windows

LI, LIS, SX, TV, DL, GP, Lui, J50-125
8099008

Flywheel holder for flywheel bgm PRO

LI, LIS, SX, TV, GP, DL with 29cm
bgm2109T

Rotor holder Casatronic (IDM ignition) 

LI, LIS, SX, TV, DL, GP
3332382

Rotor holder Casatronic (Ducati ignition

LI, LIS, SX, TV, DL, GP
3332382D

Flywheel puller and suitable holders are the only way to remove the flywheel from the cone of the crankshaft. This is required for all work on the ignition system. But also if you want or need to penetrate deeper into the innards of the engine.

The flywheel holder 2+3 windows is intended for all original Innocenti and Indian flywheels with the corresponding recesses.

The bgm PRO pole wheel has an external hexagon on which the corresponding holder is attached. The holder is supported on the nut of the large silent blocks to hold it up.

There are two variants of the Casatronic ignition, one based on the IDM ignition and the current variant manufactured by Ducati Energia. The pole wheels are blocked with two or three pins on the pole wheel with the appropriate holder.

Clutch

Clutch compressor bgm PRO 

LI, LIS, SX, TV (Series 2-3), DL, GP, J, Lui 
bgm1220TL

Clutch compressor

LI, LIS, SX, TV (Series 2-3), DL, GP, J, Lui 
7671359

Coupling holder 

LI, LIS, SX, TV (Series 2-3), DL, GP 
8099003

Both of them are irreplaceable. The compressor is used to relieve the circlip on the Lambretta clutch. After removing the ring, the coupling can be removed.
The clutch nut is tightened with 66 - 74 Nm. For both loosening and tightening the nut, the clutch basket should be blocked with the appropriate tool/holder.

brake drum puller

OEM 

LI, LIS, SX, TV, DL, GP             
7676162

CASA LAMBRETTA 

LI, LIS, SX, TV, DL, GP
8099005

MBD 

LI, LIS, SX, TV, DL, GP
3333402

In the mid-1960s the design of the brake drum was changed. At this point, the Series 2 will have three M7 threads instead of the two M6 threads previously used. This goes hand in hand with the use of the retaining ring for the cap nut on the main shaft/brake drum. Our pullers come with both M6 and M7 screws to hold the puller in place. If it is attached to the brake drum, the brake drum is pressed by the main shaft via the large central screw.

The OEM quality of the puller works, but is not the best in terms of haptics.

Casa Lambretta offers the tool in a beautiful workshop quality and it corresponds to the original Innocenti tool.

MBD has optimized the original design and features knurling on the outer edge and a ball in the tip of the central screw. This fits into the recess on the mainshaft and is intended to prevent any damage.

Headset mounting wrench MBD

LI, LIS, SX, TV, DL, GP, J, Lui 

The MBD key for the headset bearing is perfectly adapted to the Lambretta. The holder for countering is separated according to the conditions of the Lambretta.

fork spring compressor

OEM 

LI, LIS, SX, TV, DL, GP             
6660212

CASA LAMBRETTA 

LI, LIS, SX, TV, DL, GP
CBL212

MBD 

LI, LIS, SX, TV, DL, GP
7670992

The compressor for the springs in the fork is used to overhaul the fork. Neither the fork links nor the springs and their spring guide rods can be removed from the fork without compressing the springs. 

Both the Casa Lambretta and the MB compressor are based on the original design of the tool. This is sometimes a bit difficult to handle and a third or even fourth helping hand is usually not bad.

The OEM design, on the other hand, is screwed to the fork and handling is very easy and time-efficient. So here: clear purchase recommendation for OEMs.

Silent block assembly tool bgm PRO

LI, LIS, SX, TV, DL, GP

The silent blocks can only be changed with the appropriate tool and with a sufficiently heated engine housing. The bgm tool for this is a solid turned construction.

HAVING IS BETTER THAN NEEDING

crankshaft pulling sleeve 

LI, LIS, SX, TV, DL, GP             
MRB0012

Crankshaft removal tool -MBD

LI, LIS, SX, TV, DL, GP
7671543

Crankshaft pulling tool 

LI, LIS, SX, TV, DL, GP
CPX231B

It is best to pull the crankshaft into the bearing on the drive side. The original drive sleeve with the screw for the front sprocket can be used for this.

The pull-in sleeve is a length-optimized version of the original drive sleeve and offers comfort and speed when screwing. In both versions, the crankshaft must be fixed (e.g. with a connecting rod locking tool.

The Casa Performance version is a rather ingenious further development, in which the crankshaft does not have to be blocked and the shaft is drawn particularly gently into the bearing seat.

The MB tool is still the first choice for dismantling the crankshaft. It is screwed onto the motor housing and then the shaft can simply be pushed out of the bearing seat

Video CP tool

BUZZWANGLE from Sticky

The buzzwangle tool is a brilliant idea from the sticky. A digital degree disc can be clamped onto the threads for the flywheel puller using an adapter with four mounts. Thus, the digital angle dial gauge is immovably attached and both the ignition point and the control times can be determined and adjusted to an accuracy of 0,1°.

Fits all Lambretta Innocenti models and their derivatives. Just like on most Vespa and Piaggio models.

It's best if you just watch the video

NEW the video is also available with a German soundtrack

€99,00

Spark plug wrench bgm PRO SW21mm/13mm

LI, LIS, SX, TV, DL, GP, Lui, Junior

The Li family's spark plug accessibility isn't the best. The original spark plug wrench fits, of course, but has the disadvantage that removing a hot spark plug can result in burnt fingers. With the bgm part, the candle can easily be completely unscrewed by hand after loosening. And not only that, an integrated magnet holds the candle securely in the key. There are guaranteed no burnt fingers here.

€19,90

Assembly stand bgm PRO

Lambretta Series 1-3

Replaces the engine for assembly work. The assembly stand is screwed to the frame via the shock absorber attachment and the engine bolt. The scooter can then be maneuvered as if the engine were inside. Suitable both for keeping the scooter mobile and upright while the engine is on the operating table or for setting up the Lambretta after the preparation or painting when the engine is not yet ready.

€109,00

Rivet hammer for lettering

Lambretta A, B, C, LC, D, LD, LI, SX, TV, DL, GP, J, Lui

All lettering with pins on the back for attachment can be professionally attached. The pins on the lettering should be shortened so that they protrude by only 2 mm. A top tip from Dean from the Sticky Manual is to drill out the pins of the lettering. For reference page 203 Sticky Manual.

€8,90

Rivet hammer for rivet luggage compartment lock

LI, LIS, SX, TV, DL, GP

All lettering with pins on the back for attachment can be professionally attached. The pins on the lettering should be shortened so that they protrude by only 2 mm. A top tip from Dean from the Sticky Manual is to drill out the pins of the lettering. For reference page 203 Sticky Manual.

€11,95

Mounting tool shifter claw bgm PRO 'ball crusher'

LI, LIS, SX, TV, DL, GP

The ball crusher is a cleverly designed tool. With it, the shift balls and spring can be easily and conveniently installed in the main shaft. Without this tool, installing the shift dog can be a real game of patience. Simultaneously get the balls in position on both sides and enough preload without being shot into the endless expanses of the workshop by the switching spring?

Tool bag without tools CASA LAMBRETTA    

8050083

€27,99

Tool bag including on-board tools  CASA LAMBRETTA

8050083KT

€74,90

Toolkit CASA LAMBRETTA

LI (Series1-3)

3331475

Lambretta tool bag retaining clip    

The Innocenti icing on the cake of a beautiful restoration is the original on-board tool kit in the right bag with Lambretta Innocenti ribbons and then fixed with the correct retaining clip.

A nice reading recommendation on the subject of tools is the reprint of the Innocenti tool catalogue.

Tool catalog -SCOOTERPRODUCTS

Lambretta and Lambro (1960s models)     

And since the right tool is useless without knowing how to use it, here is the ultimate Lambretta reading tip! Since its release in 2004, the Sticky Manual has been the definitive repair manual for the Lambretta. The work steps are explained throughout with color illustrations. In addition to the pure repair instructions, the Sticky Manual is also an indispensable aid for identifying and distinguishing between parts.

Book -Complete Spanner's Manual Lambretta -Third Edition

by Sticky

Thanks to our friend Dean Orton, the Sticky Manual has also been available in Italian for over two years: 8100072IT